
|
|
Problem with radio resetting on 10 Metres
Problem: Has anyone figured out why the
FT1000MP vfo registers reset when > operating on 10 meters? SWR is not
excessive. K1EM
Solution: I had this problem w/10 mtrs using
an antenna similar to a G5RV. My ant was a 102ft dipole and the ladder line ran
right into the shack, right to my tuner, no remote balun, no coax. I coiled the
excess ladder line, which is not generally accepted practice, but it worked. No
more problem with reset. Got 150+ DXCC with this setup before adding 1kw AL80B.
Only major change was adding a length (12 ft) of RG213 between tuner and ladder
line, to get RF out of the shack. Coiled about 6 turns of coax in 6 inch
diameter coil outside the shack to choke off any additional RF. Now I can load
up about 400-500 watts CW on 10 mtrs with any reset. So, my problem appeared to
be excessive rf in the shack, not swr. Mike KE4DP
Radio suddenly resets to 7MHZ
SYMPTOM: I have been an owner of a 1000MP
for about a month now and have had a lot of fun with this radio. I have seen one
problem that my friends have not seen on their MP's and that is when I'm
operating on 10 meters the radio will all of a sudden reset it's self back to
7.000.00 and I will loose the settings in menu 8-9. This happens with and with
out the use of an external amp. Could this problem be due to stray RF? Anyone
else had the problem and if so what was the fix. Steve (KT0DX)
SOLUTION: I found the problem to be with the
CW Keyer being plugged into the front of the radio. When I relocated the Keyer
to the back of the radio all the RF getting into the radio went away. I can now
run the amp at full output with no problem. I usually do not use the Amp on 10
meters but the original problem was really beginning to bug me and wanted to get
it fixed. KT0DX
SOLUTION 2 I, too, had problems with my MP
doing the reset to 7.000.00 whenever more than a sniff of RF was about. I played
all sorts of tunes on cable layout, and decoupled everything going into or out
of the radio with 0.01 disc ceramics. It was worst on 10 and 15m, but 20 gave it
a go as well. It was a waste of time even switching the TL922 on! Eventually, I
got fed up enough to take the lid off. I had noticed that the problem seemed to
be at its very worst when using the internal tuner, so I started looking there.
I did not like what I saw - lots of dry looking joints. There are several large
capacitors and coils soldered into the board, and it looked as if they just had
not been hot enough. I got a monster soldering gun (60W) and re-flowed
everything I could see on the tuner board. Magic! Now I can sometimes do the
reset thing on a bad day with a following wind, so I imagine I must have missed
one or two. The difference is amazing, though. 1kW on all bands is OK, now. So
try those dry joints if you have this problem. It was well worth the effort.
John
SOME MORE THOUGHTS:Andrew, I had a similar
type problem with my FT100MP @ GM8R during CQWW CW.
I had CT keying on the rear panel and an external keyer on the front panel. When
operating on 20m the MP would lock in transmit. I removed the front panel lead
and all was well. Is the front panel jack more susceptible to RF
than the rear panel??? This was the first time I had used the MP @ GM8R normally
it would be a TS950SDX with both CT and keyer into the CW jack via a 2 way
splitter. I never tried the MP with both leads on the rear panel
jack via splitter. Wonder if you or anyone else has experience of this. The
TS950SDX does not lock up at all!
73 de GM0NAI/AC6GJ
It appears to me that two separate problems exist here. First, the ham who has
the main vfo got to 7.000 mHz when on ten meters. This is probably due to some
RF feedback. The ARRL handbook suggests various grounding methods to treat this.
Another problem a different ham had was while using his computer to key the MP
on CW. I recently had the same problem -- on 160 meters it would manifest itself
if the computer was keying the MP via the rear panel key jack. On 15 meters it
occured only if the computer was keying the MP via the front panel key jack.
These problems only occurred while running a kilowatt. I finally solved the
problem by winding the excess key wire
leads into a tight coil (several turns). With this "choke", the computer now
flawlessly keys the MP from either key jack on any band. K6NDV had a similar
problem with his computer. I believe he solved it by grounding his computer.
My keying problems were not an MP problem. Obviously, RF getting into the
computer via the key line was causing the anomaly. 73, de Earl, K6SE
I had the same thing happen when I had an external keyer hooked up for the
contest. I am sure it was RF coming in on either the external keyer or computer
keyer line. Took off the external keyer and all ok. Tom, W1TO
I had exactly this problem with my early (11/95) FT1000mp during CQWW CW at
GI0KOW. It was damned annoying! Roberts 10M yagi is about 50M away from the
shack and is 22M in the air. Admittedly it only happened when I ran the amp.
100W was no problem. I was using CT to key the rig through the rear jack and an
external
keyer in the front jack so I could use my paddle key. I found that if I removed
the keyer from the front jack, the problem
disappeared completely, so it is obviously (at least in my case) RF getting in
through the front CW keying jack. I think I'll be adding some ferrite beads on
the internal leads and also some bypass capacitors to see if I can cure it.
Hope that info starts to point you in the right direction. Andrew Williamson
GI0NWG / AC6WI
SOLUTION 3: I had the problem with resetting
all memories to 7.000 you mentioned on your web page. The cause here was an
completely different one: my power supply only provides 16/20 Amps @ 13.8V which
is ok for me because of QRP opration with max 10 W. But for testing I tried the
100 W fed into an Dipole SWR 1.2,
rig grounded. Of course voltage dropped below 10 V when transmitting shortly. As
a result everything was reset and the display showed the 7.000 kHz ... When
reducing output power to 50 W, max. current drawn from the supply ist
abt 16 A & the effect does never show up.
|